Wednesday, 18 November 2026

Jacketed Valves for Molten Sulphur & Solidifying Media

 Some process fluids become a problem the moment they cool. Molten sulphur, urea melt, concentrated ammonium nitrate solution and 50% caustic soda all solidify or crystallize at temperatures well above ambient. A standard valve in such a line can fill with solid product, seize, or crack when someone forces it. Jacketed valves solve this by keeping the body and flow path at a controlled temperature.

How a Jacketed Valve Works

A jacketed valve has a second shell around the body, and sometimes the end pieces, through which steam or hot thermic fluid circulates. Heat flows into the body wall and keeps the process fluid above its solidification point, including inside the cavity where the ball or plug sits. The jacket is a separate pressure envelope, so it has its own design pressure, inlet and outlet connections and condensate drain.

Which Media Need It

  • Molten sulphur: melts near 115 °C and flows best around 130–150 °C. Viscosity rises sharply above about 160 °C.
  • Urea melt: melting point about 133 °C.
  • Ammonium nitrate melt and concentrated solutions: crystallize as they cool.
  • 50% caustic soda: crystallizes near 12 °C.

Steam Pressure and Temperature Control

Jacket steam should match the process, not the maximum pressure available. For molten sulphur, low-pressure steam at around 3–4 bar(g) (roughly 144–152 °C saturated) keeps the fluid in its low-viscosity range, while higher-pressure steam can overheat the stream and thicken it. For ammonium nitrate, tight control prevents local overheating at the valve wall. Steam traps on the condensate outlet remove condensate promptly and prevent water hammer in the jacket.

Valve Types and Design Features

Jacketed ball, plug and globe valves are all used. Key design points include:

  • Full or partial jacket: full jackets cover the body and end connections for even heating, while partial jackets suit moderate duty.
  • Cavity relief: solid product that melts inside a closed valve expands. A vented ball or self-relieving seat prevents overpressure in the cavity.
  • Seat and seal materials: choose seats rated for the process temperature, with reinforced PTFE or metal seats for hotter fluids.
  • Stem sealing: bellow seals or high-temperature packing suit hot, hazardous media.
  • Tracing as an alternative: electric or steam tracing under insulation works for lighter duty but heats less evenly than a jacket.

Where Jacketed Valves Are Used

Typical locations include sulphur melters and pits, sulphur transfer lines to burners in acid plants, urea and ammonium nitrate solution transfer, caustic storage outlets in cold regions, and loading lines for products that solidify in transit. Jacketed valves also serve other viscous or heat-sensitive fluids such as bitumen, waxes and some resins.

Operating Practices

Heat the line and jacket before operating a valve, and never force a handwheel on a valve that may hold solid product. Temperature sensors on the valve body help confirm the cavity has reached the required temperature before operation. Keep jacket supply on during short shutdowns, and drain or purge the line before long downtime if the fluid can solidify. Inspect jackets for leaks regularly, since steam or condensate entering the process stream contaminates product and, in sulphur service, creates corrosive moisture.

Common Mistakes to Avoid

Typical errors include using steam that is too hot for the fluid, forgetting to specify a separate jacket pressure rating, leaving jackets without steam traps, and shutting off jacket supply while product remains in the line. Poor insulation over the jacket is another mistake, since it wastes steam and creates cold spots.

Specification Checklist

State the process fluid, melting point, operating temperature, process pressure, steam pressure and jacket connection size on the data sheet. Request pressure testing of both the valve body and the jacket, plus API 598 seat testing for the process side.

Application Support From Freture Techno

Freture Techno Pvt. Ltd., Mumbai, supplies valves for chemical and fertilizer plants and provides application-based valve selection. Share your fluid, temperature and steam conditions, and the engineering team will advise on a suitable configuration.

ESD Valves for Chemical & Fertilizer Plants in India

 When a reactor overheats, a line loses pressure or a toxic gas detector trips, one valve action can decide the outcome. Emergency shutdown (ESD) valves are the final element of a safety instrumented function. They move to a defined safe position when a trip signal arrives. Unlike control valves, they spend most of their life stationary, which creates distinct failure modes in corrosive plants.

How ESD Valves Differ From Control Valves

A control valve modulates continuously, so constant movement acts as a running test of the valve. An ESD valve may stay open for years and must still close within its required time on demand. In corrosive service, a stem or seat that has not moved for years can stick. That is why testing and design margins matter more than raw speed.

Functional Safety Basics

Process-plant safety instrumented systems follow IEC 61511, while device-level certification of valves, actuators and solenoids follows IEC 61508. Each safety function is assigned a Safety Integrity Level (SIL). The level achieved depends on the complete loop (sensor, logic solver and final element), not on the valve alone. Partial stroke testing (PST) moves the valve through a small fraction of its travel, typically 10–20%, to detect sticking without interrupting production. Periodic full-stroke proof tests are still required.

Design Choices That Matter

  • Fail-safe action: spring-return pneumatic actuators drive the valve to its safe position, usually closed, on loss of air or power.
  • Valve type: quarter-turn ball valves are the usual choice for tight shut-off and fast action. Define the leakage criterion, such as ISO 5208 Rate A, in the specification.
  • Solenoids and feedback: de-energize-to-trip solenoids, limit switches and position feedback confirm the final state.
  • Actuator sizing: base torque on maximum differential pressure plus a margin for breakaway torque after long static periods.
  • Fire-safe design: API 607 or API 6FA qualification helps the valve maintain shut-off if exposed to fire.
  • Closure time: set it from the process safety time, and limit it in liquid lines to avoid hydraulic shock.

Where ESD Valves Are Used

Typical locations include ammonia and chlorine storage outlets, reactor feeds, fuel gas lines to reformers and furnaces, and acid or caustic transfer headers. Plants handling hazardous chemicals in India operate under regulations such as the Manufacture, Storage and Import of Hazardous Chemical (MSIHC) Rules, which make reliable isolation a compliance matter as well as a safety one. ESD valves are also placed at tanker loading bays, where a hose or coupling failure must be isolated within seconds. Placement should be reviewed during hazard studies such as HAZOP.

Common Specification Gaps

Frequent gaps include leaving the fail-safe direction undefined, specifying a closing time without a minimum limit (risking hydraulic shock), choosing an actuator sized only for normal operating torque, and omitting a leakage criterion. Another gap is ignoring the tendency of some process fluids to leave deposits on seats, which raises torque after long idle periods.

Integration With Plant Logic

ESD valves connect to a safety PLC or logic solver, usually through hard-wired signals kept separate from the basic process control system. Position feedback from limit switches should return to the logic solver so operators can see whether the valve actually reached the safe position. Manual override and local reset arrangements should follow the plant’s safety procedures.

Maintenance and Proof Testing

Schedule proof tests at the interval assumed in the SIL calculation. Record closing times and compare trends, because a slowly increasing closing time warns of developing friction. Keep actuators and solenoids clean and dry. During planned shutdowns, stroke the valve, inspect seats for corrosion deposits and replace elastomers before they age out.

Specifying ESD Valves With Freture Techno

Freture Techno Pvt. Ltd. supplies ball valves along with valve automation and actuator integration for chemical and fertilizer plants. When requesting a quotation, state the required fail-safe position, closing time, leakage criterion and SIL target, so the right valve and actuator combination can be matched.

Caustic Soda Valves: Material & Type Selection Guide

 Caustic soda (sodium hydroxide) is used for neutralization, gas scrubbing, pH control and as a raw material in many process lines. Because it is milder than the mineral acids, valve selection is often casual. That is a mistake. Hot or concentrated caustic can crack carbon steel, crystallize in lines, and release heat when diluted. Each of these points affects valve choice.

Temperature and Concentration Limits

Carbon steel handles caustic well at ambient to moderate temperatures. As temperature rises (typically above about 60–65 °C), the risk of caustic stress corrosion cracking grows, and post-weld heat treatment or alternative materials may be required. Austenitic stainless steels are not immune to caustic cracking at higher temperatures either. For hot, concentrated caustic, nickel alloys such as Nickel 200/201 are the standard answer.

Some metals are simply incompatible. Aluminium and zinc dissolve in caustic, so galvanized or aluminium components should not appear in valves or accessories.

Crystallization in Cold Weather

A 50% caustic solution begins to crystallize near 12 °C, a temperature reached in northern Indian winters and in unheated outdoor lines. Crystallized caustic can lock a valve stem, damage seats or block the bore. Insulation with heat tracing, or jacketed valves, keeps the line above the crystallization point. After a cold shutdown, operate valves only once the line is confirmed free of solids.

Valve Types for Caustic Service

  • Ball valves: PTFE or reinforced PTFE seats suit caustic across common concentrations. Carbon steel bodies work at ambient temperature, while stainless steel or nickel alloy suits hotter duty.
  • Lined ball and plug valves: PFA or PTFE linings give full protection where product purity matters or other chemicals share the line.
  • Butterfly valves: EPDM seats resist caustic and suit large-diameter lines at moderate temperatures.
  • Globe valves: accurate throttling for dosing and neutralization control.

Avoid elastomers that swell or harden in hot caustic, and confirm compatibility for every seal and gasket.

Seat and Lining Options Compared

  • PTFE: excellent chemical resistance across all caustic concentrations, limited by temperature and cold flow under heavy load.
  • Reinforced PTFE: adds seat strength for higher pressure duty.
  • PFA lining: denser, and better where permeation or purity is a concern.
  • EPDM: suitable for butterfly seats and seals at moderate temperature, but unsuitable if hydrocarbons are present.

Safety Considerations

Diluting concentrated caustic releases significant heat, so flushing and drain procedures must be planned carefully. Leaks are dangerous because caustic burns skin and eyes. Use chemical-resistant packing such as PTFE, and fit a drain point close to the valve to support safe isolation and line clearing.

Actuation and Automation

Caustic lines are often automated for dosing and scrubber control. Pneumatic actuators on quarter-turn ball and butterfly valves suit on/off duty, while positioners with globe or control valves handle proportional dosing. Actuator options are covered under valve automation. Keep actuators and accessories clear of spills and choose corrosion-resistant coatings, because caustic mist and leaks damage paint, aluminium housings and instrument fittings. Stainless steel tubing and fittings on instrument air lines add further protection.

Where Caustic Soda Valves Are Used

Typical locations include scrubber circulation loops, neutralization and pH control skids, caustic storage and tanker unloading, and dilution stations. Plants making soaps, detergents, textile chemicals, pulp and alumina also run extensive caustic networks, often at elevated temperature where material choice becomes critical.

Common Mistakes to Avoid

Typical mistakes include fitting galvanized or aluminium parts, ignoring winter crystallization in outdoor lines, and using elastomers selected for water rather than for hot caustic.

Specification Tips

State concentration, temperature range and any dilution scenario on the data sheet. Specify ASME B16.34 ratings, API 598 test requirements and full material certificates. For stainless steel or nickel components, ask for positive material identification (PMI) to confirm the correct alloy.

Valve Supply From Mumbai

Freture Techno Pvt. Ltd. manufactures ball, plug, globe, butterfly and lined valves for chemical and fertilizer plants. Share your caustic concentration, operating temperature and pressure, and the team will recommend suitable body materials, seats and construction.

Valves for Hydrochloric Acid & Chlorine Service in India

Hydrochloric acid and chlorine are used across chemical plants making PVC intermediates, chlorinated solvents, bleach, dyes and agrochemical intermediates. Both are toxic, and both attack common valve materials in ways that surprise first-time buyers. Standard stainless steel, for example, is a poor choice for either when moisture is present. Choosing the right valve starts with one question: is the stream wet or dry?

Hydrochloric Acid Service

Aqueous hydrochloric acid (HCl) corrodes carbon steel and austenitic stainless steel quickly, and chlorides drive pitting. Practical options are fluoropolymer-lined valves (PTFE, PFA), rubber-lined valves for lower temperatures, and nickel-molybdenum alloys such as Hastelloy B-3 or C-276 for demanding duty. B-3 performs well in pure HCl but not where ferric or other oxidizing ions are present.

Anhydrous (dry) hydrogen chloride gas behaves differently. It is far less aggressive toward steel until moisture enters, which makes moisture control, not only metallurgy, the key to valve life.

Chlorine Service: Wet vs Dry

Dry chlorine is commonly handled in carbon steel valves, because a protective film forms on the metal when moisture is very low. Wet chlorine is far more corrosive. It forms hydrochloric and hypochlorous acids that destroy carbon steel and stainless steel. Titanium and PTFE or PFA lining are the usual answers for wet chlorine.

One critical warning: titanium can ignite in dry chlorine, so it must never be specified for dry service. Every valve data sheet should state clearly whether the chlorine is wet or dry. Guidance from The Chlorine Institute is widely followed for materials, cleanliness and valve design in chlorine systems.

Lined Plug and Ball Valves

PTFE and PFA lined valves are the mainstay for both media. A fully lined body, plug or ball and stem keeps metal away from the process fluid. Their limitation is permeation, because HCl and chlorine can diffuse slowly through fluoropolymer. Vent holes in the steel body let permeate escape instead of corroding the shell from the inside. PFA, being denser, generally resists permeation better than PTFE. Spark testing of the lining confirms integrity before dispatch, and flange faces should be inspected for lining damage on arrival.

Bellow Seal Valves for Toxic Duty

Chlorine and HCl vapour are inhalation hazards. A conventional packed stem can weep over time, so bellow seal globe valves, which seal the stem with a welded metal bellows, are often chosen for hazardous lines. Bellows also remove the need for periodic gland tightening, a task that exposes maintenance staff to fumes. For chlorine, confirm that the bellows metallurgy suits the wet or dry condition.

Where These Valves Are Used

HCl valves appear in acid synthesis, absorption, storage and tanker loading, pickling and etching lines, and pH adjustment systems. Chlorine valves appear at electrolysis outlets, liquefaction, storage, and feeds to reactors making chlorinated organics, bleach and disinfectants. In both cases, the highest-risk points are unloading stations and transfer lines, where hoses, connections and frequent operation raise the chance of leaks.

Selection Checklist

  • Wet or dry stream, and acid concentration
  • Operating temperature and pressure, including upsets
  • Oxidizing contaminants such as ferric ions or free chlorine in HCl
  • Lining or alloy choice, with body vents for permeation
  • Cleanliness level for chlorine service
  • ASME B16.34 ratings, with shell and seat tests to API 598

Common Mistakes to Avoid

Typical errors include specifying 316 stainless steel for a “small” HCl line, assuming a titanium valve suits all chlorine duty, forgetting body vents on lined valves, and approving a valve without checking seat, seal and gasket materials as well as the body. Another frequent mistake is treating wet and dry chlorine as one case, when a valve that suits one can fail quickly in the other.

Sourcing From India

Freture Techno Pvt. Ltd., Mumbai, manufactures lined, ball, plug, globe, butterfly and bellow seal valves for chemical and fertilizer plants. Send your media, concentration and operating conditions, and the engineering team will advise on the correct lining, alloy and valve type.

Nitric Acid & Ammonium Nitrate Valves for Fertilizer Plants

 Nitric acid and ammonium nitrate (AN) sit at the centre of nitrogen fertilizer production. Ammonia is oxidized to nitric acid, which is then neutralized with more ammonia to make AN solution for CAN, NP and NPK grades. The two streams ask different things of a valve. Nitric acid is strongly oxidizing, while AN is sensitive to contamination, heat and confinement. Valve selection here is as much about safety as corrosion.

Valves for Nitric Acid Service

Nitric acid attacks carbon steel rapidly, but austenitic stainless steels form a stable passive film in oxidizing conditions. Low-carbon 304L and 316L are the workhorse grades in absorption and transfer lines, because the low carbon content limits intergranular attack near welds. For hotter or more concentrated streams, titanium, zirconium or high-silicon stainless alloys are used.

Because nitric acid is a strong oxidizer, valves should arrive degreased and free of hydrocarbon lubricants, since organic contamination can react with the acid. PTFE seats and packing are compatible and widely used. Nitrous fumes in tail-gas lines are toxic, so bellow seal globe valves are a sound choice where stem leakage must be eliminated.

Valves for Ammonium Nitrate Service

AN solutions and melts are not aggressive toward stainless steel, but they are hazardous if mishandled. Decomposition risk rises sharply with contamination, confinement and overheating. Good valve design addresses each:

  • Material: 304L or 316L stainless steel. Avoid carbon steel, copper, zinc, lead and brass, which contaminate the product or react with it.
  • Cleanliness: no hydrocarbon grease, oil or organic sealants in the flow path.
  • Cavity relief: a closed ball valve can trap hot AN solution in the body cavity. Self-relieving seats or a vented ball let pressure escape to the upstream side.
  • No dead pockets: full-bore designs and minimal cavities reduce places where product can stagnate and overheat.
  • Temperature control: concentrated solutions crystallize on cooling, so steam-traced or jacketed valves are common. The heating medium must be controlled to avoid local overheating.

Valve Types and Configurations

Stainless steel floating and trunnion ball valves give tight shut-off in AN transfer and acid feed lines. Stainless globe valves provide throttling on neutralizer feed lines. Butterfly valves with suitable seats serve large-diameter, low-pressure solution and cooling lines. Always specify temperature-rated seat materials, because AN melt temperatures can approach the working limit of standard PTFE seats. Where positive isolation of a heated line is needed for maintenance, double block and bleed arrangements add a verified, vented barrier between the plant and the work area.

Where These Valves Are Used

Nitric acid valves are found in ammonia oxidation and absorption sections, acid storage and transfer, and neutralizer feed lines. Ammonium nitrate valves appear at neutralizer outlets, evaporator feeds, melt transfer lines to prilling or granulation, and solution storage. Products such as CAN and NPK can use AN solution as a feedstock, so the same selection logic extends into those blocks.

Cleanliness and Maintenance Discipline

Because AN is sensitive to contamination and heat, plants treat cleanliness and temperature limits as design inputs rather than operating tips. Keep dedicated spares for AN service, keep greases and thread sealants out of the work area, and make sure overhaul procedures do not introduce contamination. Clear tagging and material records help prevent a wrong-material swap during turnarounds.

Verification Before Dispatch

Request material test certificates with positive material identification (PMI), since a wrong alloy is a real risk in oxidizing service. For nitric acid duty, buyers sometimes specify ASTM A262 Practice C (the Huey test) to confirm resistance to intergranular attack. Pressure ratings follow ASME B16.34, and shell and seat testing follows API 598.

Working With Freture Techno

Freture Techno Pvt. Ltd. manufactures stainless steel ball, globe, butterfly and bellow seal valves, along with other industrial valves, for nitrogen fertilizer and chemical plants. Provide the stream concentration, temperature, pressure and cleanliness requirement, and the team will recommend a configuration suited to the duty.

Sulphuric Acid Valves for Chemical & Fertilizer Plants in India

Sulphuric acid is the backbone of fertilizer manufacturing. It digests phosphate rock, feeds single super phosphate (SSP) lines and goes into ammonium sulphate production. Yet few media are as unforgiving on valves, because corrosion behaviour changes sharply with concentration, temperature and flow velocity. A material that lasts years in 98% acid can fail within months in a 40% stream. Choosing sulphuric acid valves starts with understanding that curve.

Why Concentration Decides the Valve Material

In concentrated acid (roughly 93–98%), carbon steel builds a protective iron sulphate film, so carbon steel bodies are common at ambient temperature. The weakness is velocity. Turbulence around seats, discs and trim strips that film and speeds up attack, which is why trim is usually upgraded to 316L or Alloy 20 even when the body stays carbon steel.


Dilute and intermediate concentrations behave the opposite way. Carbon steel corrodes quickly, and standard 304 or 316 stainless steel can struggle, especially as temperature rises. These zones appear wherever acid meets water: absorption towers, acid coolers, rinse lines and any point where moisture gets in.

Material Options for Sulphuric Acid Service

  • Alloy 20 (UNS N08020): a long-established choice across a wide concentration range at moderate temperatures, widely used for gate and globe valves.
  • Hastelloy B-3: strong in dilute-to-moderate hot acid, but unsuitable where oxidizing contaminants such as ferric ions are present.
  • Hastelloy C-276: preferred when oxidizing impurities are expected.
  • PTFE, PFA or FEP lined valves: cover most concentrations, limited mainly by the lining’s temperature rating.

Valve Types and Where They Fit

Lined plug and ball valves isolate acid transfer lines with tight shut-off. Alloy gate and globe valves handle isolation and throttling in hot or intermediate-strength acid where metal construction is preferred. Bellow seal globe valves remove stem leakage, which matters because acid mist attacks nearby steelwork and is a health hazard. Lined butterfly valves suit large-diameter circulation and cooling loops.

Design Details That Prevent Failures

  • Body vents on lined valves: acid can permeate fluoropolymer liners slowly. Vent holes let it escape before it corrodes the steel shell behind the liner.
  • Velocity control: size lines and valves to keep acid velocity low wherever carbon steel is used.
  • Stem sealing: use chemical-resistant packing or bellow seals instead of standard packing.
  • Drain and vent points: diluting acid releases heat, and dilute acid attacking steel generates hydrogen, a flammable gas. Isolation points need safe venting and drainage.

Where Sulphuric Acid Valves Are Used

In fertilizer plants, sulphuric acid valves sit at acid storage and day tanks, digestion and reactor feed lines, SSP mixing circuits, ammonium sulphate neutralizers and tanker loading points. Chemical plants add dye and pigment intermediates, metal pickling lines and effluent neutralization. Each location has its own concentration, temperature and velocity profile, so one valve specification rarely fits an entire plant.

Common Failure Signs

Early warning signs include pitted trim, seat leakage after a period of stable service, and stems that stiffen as sulphate deposits build up. Lined valves may show blistering or staining around the body flange, which suggests permeation. Treat these signs as a prompt to review material and velocity, not only to replace the part. Fitting a like-for-like valve into a line that is already failing usually repeats the failure within months.

Standards and Testing

Specify ASME B16.34 for pressure–temperature ratings, ASME B16.5 flanged ends, and shell and seat testing to API 598, with the shell test run hydrostatically at 1.5 times the rated pressure. For lined valves, request spark (holiday) testing of the lining. For alloy parts, ask for positive material identification (PMI) so the correct grade is confirmed before dispatch.

Choosing a Supplier

Freture Techno Pvt. Ltd., Mumbai, manufactures ball, plug, gate, globe, butterfly and bellow seal valves, including lined constructions, for chemical and fertilizer plants. Share your acid concentration, temperature and pressure, and the engineering team can recommend the right body, lining and trim for your line.

Thursday, 20 August 2026

Best Industrial Valves for Chemical & Fertilizer Plants in India | Freture Techno Pvt. Ltd.

Modern chemical and fertilizer plants operate continuously under aggressive temperatures, corrosive fluids, and abrasive process media. The reliability of every production line depends on properly engineered valves that provide precise isolation, dependable flow control, and long operational life.

Freture Techno Pvt. Ltd. offers a complete range of industrial valves specifically developed for chemical manufacturing and fertilizer processing facilities across India.

Critical Challenges in Chemical Processing

Process engineers commonly face:

  • Corrosion caused by strong acids

  • Erosion from slurry movement

  • Stem leakage of hazardous gases

  • High-pressure process conditions

  • Frequent maintenance shutdowns

Low-emission and corrosion-resistant valve designs help overcome these operational challenges.

Recommended Valve Solutions

PTFE & PFA Lined Ball Valves

These valves isolate highly corrosive chemicals while protecting metallic valve bodies from chemical attack. They are extensively used in acid transfer and chlorinated chemical processes.

Bellow Seal Globe Valves

Ideal for toxic and hazardous media, bellow seal valves prevent atmospheric leakage and comply with stringent emission control requirements.

High-Performance Butterfly Valves

Suitable for cooling water, utility systems, and large process pipelines where lightweight construction and low torque operation are required.

Instrumentation Valves

Needle valves, manifolds, and monoflanges provide accurate pressure measurement and safe instrument isolation throughout chemical plants.

Features of a Reliable Chemical Valve

A high-quality industrial valve should include:

  • Anti-blowout stem design

  • Fire-safe construction

  • Low fugitive emissions

  • Precision-machined sealing surfaces

  • Corrosion-resistant trim materials

  • Hydrostatic and seat leakage testing

These features improve operational safety while reducing maintenance frequency.

Industries Served

Freture Techno Pvt. Ltd. supplies valve solutions for:

  • Chemical manufacturing

  • Fertilizer plants

  • Petrochemical industries

  • Pharmaceutical processing

  • Water treatment facilities

  • Oil & Gas terminals

  • Specialty chemical production

Engineering Support

Beyond manufacturing, the company provides application-based valve selection, actuator integration, material recommendations, and customized automation packages to suit individual process requirements.

Conclusion

Whether handling phosphoric acid, ammonia, solvents, or abrasive slurry, choosing the correct industrial valve improves plant efficiency and minimizes operational risks. Best Industrial Valves for Chemical & Fertilizer Plants in India, Freture Techno Pvt. Ltd. delivers engineered valve solutions trusted by process industries throughout India.

Jacketed Valves for Molten Sulphur & Solidifying Media

 Some process fluids become a problem the moment they cool. Molten sulphur, urea melt, concentrated ammonium nitrate solution and 50% causti...